manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 273 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 273

Chapter 7 System configuration using the CLI

273

System Configuration Guide

 

Figure 100   

show cli command output

Displaying system information

The 

show sys-info

 command displays the current system characteristics.

The syntax for the 

show sys-info 

command is:

show sys-info

The 

show sys-info 

command is in the privExec command mode.

The 

show sys-info 

command has no parameters or variables. 

Figure 101

 displays sample output from the 

show sys-info 

command.

Note: 

You must have SNTP enabled and configured to display GMT 

time.

425-48T(config)#show cli info

Inactivity Timeout:  15 minute(s)

Login Timeout:  1 minute(s)

Login Retries:  3

More:  True

Screen Lines:  23

425-48T(config)#RW     RW        ***************

RO     RO        ***************

425-48T#

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments