manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 230 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 230

230

Chapter 6 System configuration using the Console Interface

320985-A Rev 01

 

Primary RADIUS Server

The IP address of the Primary RADIUS server.

Default

0.0.0.0 (no IP address assigned)

Range

Four-octet dotted-decimal notation, where each octet is 
represented as a decimal value, separated by a decimal point

Secondary RADIUS 
Server

The IP address of the Secondary RADIUS server.

Default

0.0.0.0 (no IP address assigned)

Range

Four-octet dotted-decimal notation, where each octet is 
represented as a decimal value, separated by a decimal point

RADIUS UPD Port

The user datagram protocol (UDP) port for the RADIUS server.

Default

1645

Range

0 to 65536

RADIUS Shared Secret

Your special switch security code that provides authentication to the RADIUS 
server.

Default

Null string (which is not authenticated)

Range

Any contiguous ASCII string that contains at least 1 printable 
character, up to a maximum of 35

Table 50   

Console/Comm Port Configuration screen fields (continued)

Field

Description

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments