manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 207 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 207

Chapter 5 Using the Web-based management interface

207

System Configuration Guide

 

Viewing stack information

You can view a summary of your stack framework, for example, the current 
version of the running software and the IP address of the Web-based management 
interface.

To view stack information:

1

From the main menu, choose

 Summary > Stack Information

.

The 

Stack Information

 page opens 

(Figure 76)

.

Manufacturing Data 
Code

The date of manufacture of the board in ASCII format.

Hardware Version

The hardware version of the policy switch.

Serial Number

The serial number of the policy switch.

Operational State

The current operational state of the device. The operational states are: Other, Not 
Available, Removed, Disabled, Normal, Reset in Progress, Testing, Warning, Non 
Fatal Errors, Fatal Error, and Not Configured.

Mac Address

The mac address of the switch.

IP Address

The IP address of the switch.

Power Status

The power status of the switch.

Fans Status

The fan status of the switch. 

Note: 

The Web-based management user interface automatically detects 

the operational mode of your system. If the system is in standalone 
mode, the 

Stack Information

 page is not an option listed in the menu.

Table 44   

Switch Information page fields

Item

Description

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments