manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 101 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 101

Chapter 2 Using the console interface

101

System Configuration Guide

 

Figure 19   

System Characteristics screen

Table 15   

System Characteristics screen fields

Field

Description

Operation Mode

Read-only field that indicates the operation mode of the unit, for example:

•

When the unit is part of a stack configuration, the (read-only) field indicates the 
unit is operational in a stack, and lists the current unit number of this switch. 

•

When the unit is 

not

 part of a stack configuration (operating standalone), the 

read-only field indicates the unit is operating as a switch. When in this operation 
mode, the Size of Stack and Base Unit fields (see following description) do not 
appear.

Size of Stack

This read-only field only appears when the switch is participating in a stack 
configuration. This field indicates the number of units configured in the stack 
configuration (1 to 8 units maximum).

Base Unit

This read-only field only appears when the switch is participating in a stack 
configuration. This field indicates the unit number of the switch that is currently 
operating as the base unit.

 System Characteristics

Operation Mode:   Switch

MAC Address:      00-0F-CD-BF-1E-80

Reset Count:      9

Last Reset Type:  Management Reset

Power Status:     Primary Power

Local GBIC Type:  port 49, None

                  port 50, None

sysDescr:         Ethernet Switch 425-48T

                  HW:00       FW:3.5.0.2 SW:v3.6.0

sysObjectID:      1.3.6.1.4.1.45.3.57.1

sysUpTime:        7 days, 17:49:05     sysNtpTime: SNTP not synchronized.

sysServices:      3

sysContact:       [  ]

sysName:          [ Ethernet 428-48T ]

sysLocation:      [  ]

Enter text, press <Return> or <Enter> when complete.

Press Ctrl-R to return to previous menu.  Press Ctrl-C to return to Main Menu.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments