manualshive.com logo in svg

Nortel 1800, Installing

Share
Download
Nortel 1800 Installing Download Page 54

54

317808-D

Environmental specifications

Regulatory compliance

In addition to all Regulatory Compliance requirements specified elsewhere in this 
manual, all fiber optic modules (SFPs) used in this equipment shall meet the 
applicable Laser Standards for Compliance. These standards are as follows: 

1800-24T-LX-DC and 1800-24T-DC (DC power supply) 
interface options

1000BASE-LX port for the 1800-24T-LX-DC

Operating temperature:

–10 to 85 °C

Storage temperature:

–40 to 85 ºC

Laser eye safety:

FDA 21(J) CFR, Certificate 9210176-16

EN 60950, Certificate R2179338.01

EN 60825-1

EN 60825-2

Electrical safety:

CLASS 3862.07

Certificate CSA 1034405

CLASS 3862.87

10BASE-T/100BASE-TX

RJ-45 (8-pin modular) connectors

1000BASE-LX port

Long wavelength 1300 nm duplex SC type fiber 
optic connector to connect devices over single 
mode fiber optic cable (5 km, 10 µm core)

Physical specifications

Height:

12 mm

Width:

30 mm

Depth:

65 mm

Weight:

n/a

Connector type

Duplex SC

Summary of Contents for 1800































































Reviews:

No comments

Brands by name

Popular brands

Load more brands