Nortek 1RP24K Series Installation Instructions Manual Download Page 16

INSTALLATION CHECKLIST

INSTALLATION ADDRESS:

CITY:

STATE:

UNIT MODEL #:

UNIT SERIAL #:

INSTALLER NAME:

CITY:

STATE:

Unit Installed Minimum clearances per 

Figure 1 (page) 3

?

YES

NO

Has the owner’s information been 

reviewed with the customer?

YES

NO

Has the Literature Package been left 

with the unit?

YES

NO

REFRIGERATION SYSTEM

Was unit given 24 hr warm up period 

for crankcase heaters?

YES

NO

Stage-1 Liquid Pressure (high side):

Stage-1 Suction Pressure (low side):

Specifications & illustrations subject to change without notice or incurring obligations (07/22).
O’Fallon, MO, © Nortek Global HVAC LLC 2022. All Rights Reserved.

REPLACEMENT PARTS

Replacement parts are available through your distributor. 

Please have the complete model and serial number of the 

unit when ordering replacement parts.

ELECTRICAL:

Capacitors

Temperature Limit Switches

Compressors

Thermostats

Contactors

Time Delay Relays

Pressure Switches

Transformers

Relays

MOTORS:

Blower Motor

Fan Motor

COMPONENTS:

Blower Assembly

Fan Grille

Cabinet Panels

Filter/Driers

Expansion Valves

10434500

(NEW)

ELECTRICAL SYSTEM

Electrical connections tight?

YES

NO

Line voltage polarity correct?

YES

NO

Rated Voltage:

Has the thermostat been calibrated?

YES

NO

Is the thermostat level?

YES

NO

Is the heat anticipator setting correct? 

(If Applicable)

YES

NO

Summary of Contents for 1RP24K Series

















Reviews: