Home
/
Norstar
/
Voice Mail 4.0
/
Set Up And Operation Manual

Norstar Voice Mail 4.0, Set Up And Operation Manual, Page: 223 / 258

Share

Page: 223 / 258

Norstar Voice Mail 4.0 Set Up And Operation Manual Download Page 223

P0886600 Issue 1.0

Set Up and Operation Guide

Appendix B: Norstar Configuration Tips and

Norstar Feature Compatibility

Overview

This appendix describes some Norstar configuration enhancements that can
maximize the efficiency of Norstar Voice Mail.

Note: The features and capabilities of Norstar vary, depending on the type of

Norstar Integrated Communication System (ICS) you are using, as well as
the number and type of lines provided by your telephone company.
Problems will arise when you configure to use features which are not
supported or available. For example, you cannot use incoming telephone
lines for Off-premise Message Notification or Outbound Transfer. Features
that are incorrectly configured or not available will likely fail or respond
unexpectedly.

Refer to the documentation that came with your ICS for more information

Delayed answering by the Norstar Voice Mail Automated Attendant

The Norstar Voice Mail Automated Attendant can answer any call on specified
Central Office (CO) telephone lines after a specified number of rings. Norstar Voice
Mail answers incoming calls when:

1. The installer programs Norstar Voice Mail to be the prime telephone for one

or more designated CO lines. The Norstar Delay Ring Transfer (DRT) feature
transfers unanswered calls on these lines to the Norstar Voice Mail Automated
Attendant after the specified number of rings.

Note: The Norstar DRT feature applies only to incoming calls on the assigned line.

It does not affect any DN calls between telephones.

«
...
221
222
223
224
225
...
»

Summary of Contents for Voice Mail 4.0



































































































































































































































































Reviews:

No comments