Norsat WAYFARER WFM090KU-RC User Manual Download Page 15

Page: 15 / 32

DOC-000898 Rev B 07/2020

4.3.2. Reflector

1. Set the EL angle to 10 degrees for ease of assembly. Refer to Section 5.3.2. for elevation adjustment.

2. Take out the Center Reflector Hub from Case 1.
3. Install the Center Reflector Hub by aligning the mating central Hub petals on the Pedestal Assembly and then

lock the Hub into place by rotating it clockwise.

4. Take out the Petals from Case 1.

Note: Each petal is labeled with a matching number to indicated where it is installed on the Reflector Hub.

5. First install Petal 1 by first inserting the locating stubs on the petal into the Reflector Hub. Then engage the hub-

side latches.

Note: Exercise caution when installing the first two petals because petals are not self-supporting until 1 set

of petal-side latches have been engaged.

Petal-Side Latch

Hub-Side Latch

Summary of Contents for WAYFARER WFM090KU-RC
































Search results

Summary of Contents for WAYFARER WFM090KU-RC

Reviews:

Brands by name

Popular brands

Norsat WAYFARER WFM090KU-RC, User Manual

Search results

Summary of Contents for WAYFARER WFM090KU-RC

Reviews:

Brands by name

Popular brands