Noritz proTOUGH NR981-DVC Installation Manual Download Page 1

Potential dangers from accidents during installation and use are divided into the following three 
categories. Closely observe these warnings, they are critical to your safety.

Prohibited

Disconnect
Power

Ground

Be sure to do

WARNING:

 If the information in this manual is not followed exactly, a 

fi

re or explosion may result 

causing property damage, personal injury or death.

NORITZ AMERICA 
CORPORATION

 Installation Manual

TANKLESS GAS WATER HEATER

NR981-DVC

 (Indoor Installation)

DANGER indicates an imminently hazardous situation which, 

if not avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, 
if not avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, 
if not avoided, may result in minor or moderate injury.

DANGER

WARNING

CAUTION

Requests to Installers

•  In order to use the water heater safely, read this installation manual carefully, and follow the in-

stallation instructions.

•  Failures and damage caused by erroneous work or work not as instructed in this manual are not 

covered by the warranty.

•  Check that the installation was done properly in accordance with this Installation Manual upon  

completion.

After completing installation, please either place this Installation Manual in a plastic pouch and 

attach it to the side of the water heater (or the inside of the pipe cover or recess box if applicable), 

or hand it to the customer to retain for future reference.  Also, be sure to 

fi

ll in all of the required 

items on the warranty and to hand the warranty to the customer along with the Owner's Guide.

CAUTION

SBA8871-2

Rev. 03/13

FOR USE IN RESIDENTIAL APPLICATIONS.
Installation must conform with local codes, or in the absence of local codes, 
the National Fuel Gas Code, ANSI Z223.1/NFPA 54- latest edition and/or 

CSA B149.1, Natural Gas and Propane Installation Code (NSCNGPIC).

Noritz America reserves the right to discontinue, or change at any 

time, the designs and/or speci

fi

cations of its products without notice.

Low NOx 

Approved by 

SCAQMD

14 ng/J or 20 ppm

(Natural Gas Only)

CERTIFIED

R

*SBA8871*

Summary of Contents for proTOUGH NR981-DVC


































Reviews: