Nordson PermaFlo 830 Customer Product Manual Download Page 88

Page: 88 / 102

Hydraulic Section Parts

D 2-4

Part 1022914G03

2007 Nordson Corporation

Type U Hydraulic Section

−

Revisions E and Above

See Figure D 2-2 for part locations.

Item

Part

Description

Quantity

Note

1021873

PUMP, hydraulic, assembly, PermaFlo 830, Type U

1022003

CUP, solvent, PermaFlo 30:1

- - - - - -

ADAPTER, female, PermaFlo 830

- - - - - -

RING, V, UHMWPE

- - - - - -

ADAPTER, male, PermaFlo 830

1021878

HOUSING, upper, hydraulic, PermaFlo 830

1042327

PLUNGER, hydraulic, PermaFlo 830

900023

BALL, 440 stainless steel, 0.750 in., 50

- - - - - -

SEAT, ball, pressure, PermaFlo 830

- - - - - -

O-RING, PTFE, 2.234 x 2.512 x 0.139 in.

1021892

HOUSING, pressure, hydraulic, PermaFlo 830

942310

O-RING,

−

231, Buna-N, 70 duro

1021896

CAGE, ball, siphon, PermaFlo 830

900050

BALL, 440 stainless steel, 1.250 in., 100

- - - - - -

SEAT, ball, 1.25 in. diameter

- - - - - -

O-RING, PTFE, 2.050 x 2.256 x 0.103 in.

C, E

1021950

HOUSING, siphon, PermaFlo 830

NOTE A: Noted parts are included in packing kits. Refer to

Packing Kits

on the following pages.

B: Noted parts are included in the Hydraulic Seal Kit, part 1063360.
C: Noted parts are included in the Pressure Ball Check Kit, part 1027525.
D: Noted parts are included in the Siphon Ball Check Kit, part 1027526.

Summary of Contents for PermaFlo 830







































































































Search results

Summary of Contents for PermaFlo 830

Reviews:

Related manuals for PermaFlo 830

Brands by name

Popular brands

Nordson PermaFlo 830, Customer Product Manual

Search results

Summary of Contents for PermaFlo 830

Reviews:

Related manuals for PermaFlo 830

Brands by name

Popular brands