Nordson PermaFlo 830 Customer Product Manual Download Page 48

Page: 48 / 102

Air Motor Repair

C 1-5

Part 1022914G03

2007 Nordson Corporation

Air Pilot Valve Repair

−

Pump Revisions D and Above

NOTE:

The pilot valves on pump revisions D and above consist of

individual components assembled into the upper and lower cylinder heads.

For air motors with cartridges, refer to the procedure on the preceding page.

The actuator and 3-way valve components are available as kits.

See Figure C 1-4. All components of the air pilot valves, except the cup

seal, can be removed and replaced without disassembling the air motor.

1300565A

Apply MagnaLube-G or equivalent

PTFE grease to external O-rings

before installing.

Actuator Kit

3-Way Valve Kit

Figure C 1-4 Air Pilot Valve (Actuator and Valve) Assembly

−

Pump Revisions D and Above

4A. Plug cap
4B. Plug with spring guide
4C. Spring
4D. Plunger assembly

4E. Cup seal

4F. Plug

5A. Plug with O-ring

5B. Spring
5C. Valve cartridge
5D. Ball

Summary of Contents for PermaFlo 830







































































































Search results

Summary of Contents for PermaFlo 830

Reviews:

Related manuals for PermaFlo 830

Brands by name

Popular brands

Nordson PermaFlo 830, Customer Product Manual

Search results

Summary of Contents for PermaFlo 830

Reviews:

Related manuals for PermaFlo 830

Brands by name

Popular brands