Nordson PermaFlo 830 Customer Product Manual Download Page 47 | Manualshive

Page: 47 / 102

background image

Air Motor Repair

C 1-4

Part 1022914G03

E

2007 Nordson Corporation

Air Pilot Valve Cartridge Replacement (Pump Revisions A

−

C)

NOTE:

The air pilot valves on pump revisions A through C consisted of an

actuator cartridge and a valve cartridge. One valve set is installed in each

cylinder head. Use this procedure to replace the cartridges. For air motors

without cartridges, refer to the procedure on the following page.

See Figure C 1-3.

1. Remove the screws (4) and flat washers (5) securing the actuator and

valve cartridges (6 and 10) in the cylinder heads.

2. Remove the valve cartridges, then the actuator cartridges. Use pliers if

necessary. Do not damage the housings.

3. Lubricate the external O-rings of the new cartridges with PTFE grease.
4. Install the actuator cartridges into the cylinder heads with the holes in

the flats facing toward the valve cartridge bores.

5. Push the valve cartridges into the air cylinder heads.

NOTE:

You may need to lightly tap on the cartridges with a soft mallet to

engage the O-rings. When installed correctly the flat ends of the valve

cartridges are flush against the actuator cartridges flats and the valve

balls (10A) poke through the holes in the flats to contact the actuator

plungers (6A).
6. Re-install the screws and flat washers to secure the cartridges.
7. Make sure the plastic caps (7) are installed on the actuator cartridge

heads to prevent debris from entering the cartridge.

1300388A

6

4

5

10

5

4

Apply MagnaLube-G or equivalent

PTFE grease to external O-rings

before installing.

6

10

7

10A

6A

Figure C 1-3 Air Pilot Valve (Actuator and Three-Way Valve Cartridge) Replacement

−

Pump Revisions A

−

C

4. Washer-head screws
5. Flat washers
6. Actuator cartridge

6A. Actuator plunger

7. Plastic cap

10. Valve cartridge

10A. Valve ball

«
...
45
46
47
48
49
...
»

Summary of Contents for PermaFlo 830







































































































Reviews:

No comments

Related manuals for PermaFlo 830

PELLEMATIC SmartXS

Brand: MAINE ENERGY SYSTEMS Pages: 82

Brand: valent Pages: 20

Brand: Panasonic Pages: 55

Optyma Blue OP-LGHE068NTA07D

Brand: Danfoss Pages: 8

Brand: Enerpac Pages: 10

Brand: WilTec Pages: 8

Brand: Vallfirest Pages: 32

Point-of-Use Drinking Water System

Brand: R-Can Pages: 12

MAESTRO SMART 9HP

Brand: Olimpia splendid Pages: 52

Brand: A.O. Smith Pages: 74

Brand: baracuda Pages: 14

Brand: Samoa Pages: 40

Pneumatic Oilpump 3:1

Brand: Pressol Pages: 28

Inverboost Premium 10kW

Brand: AQS Pages: 49

Brand: Penguin Pages: 10

Brand: Pittsburgh Pages: 4

OMNIA S HYBRID C 3.2

Brand: Ferroli Pages: 88

Brand: VOKERA Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands