Nordson PermaFlo 830 Customer Product Manual Download Page 44

Page: 44 / 102

Air Motor Repair

C 1-1

Part 1022914G03

2007 Nordson Corporation

Section C 1

Air Motor Repair

WARNING:

Allow only qualified personnel to perform the following tasks.

Follow the safety instructions in this document and all other related

documentation.

WARNING:

Shut off and lock out the compressed air supply to the pump

and relieve system fluid pressure before servicing the pump or other system

components. Failure to observe this warning may result in serious personal

injury.

Introduction

This section contains procedures for:

Coupling removal and replacement

Air motor rebuild

Air valve rebuild

NOTE:

Part numbers in illustrations match the item numbers in

Section D1

Air Motor Parts

. Lettered parts are part of the hydraulic section and are

shown in

Sections C2 Hydraulic Section Repair

and

Section D2 Hydraulic

Section Parts

Tools and Materials Required

The following tools and materials are needed to repair the air motor:

16-

and

-in. socket wrenches

Small and large adjustable wrenches

-in. hex wrench

Flat-bladed screwdriver

Rubber mallet

Large pliers or vice grips

Large, flat, clean work bench

MagnaLube-G or equivalent PTFE-impregnated grease (Nordson

part 900349)

Loctite 242 Removable thread adhesive or equivalent (Nordson
part 900464)

Replacement parts or kits (refer to

Section D1 Air Motor Parts

)

Summary of Contents for PermaFlo 830







































































































Search results

Summary of Contents for PermaFlo 830

Reviews:

Related manuals for PermaFlo 830

Brands by name

Popular brands

Nordson PermaFlo 830, Customer Product Manual

Search results

Summary of Contents for PermaFlo 830

Reviews:

Related manuals for PermaFlo 830

Brands by name

Popular brands