Nordson PermaFlo 830 Customer Product Manual Download Page 20

Page: 20 / 102

Safety

B 1-5

Part 1022914G03

2007 Nordson Corporation

Safety Labels

Table B 1-1 contains the text of the safety labels on the pump. The safety

labels are provided to help you operate and maintain your pump safely. See

Figure B 1-1 for the location of the safety labels.

Table B 1-1 Safety Labels

Item

Part

Description

600179

WARNING

HIGH PRESSURE DEVICE

Read instruction manual before operation and observe all

warnings.

INJECTION HAZARD

Airless spray painting equipment can cause serious injury if the

spray penetrates the skin. Do not point the gun at anyone or any

part of the body. In case of penetration, adequate medical aid

must be immediately obtained.

COMPONENT RUPTURE

This system is capable of producing high pressure. Please refer

to the data plate on the hydraulic section. To avoid rupture and

injury, do not operate this pump at a pressure higher than the

rated maximum working pressure of any component in the

system (including but not limited to spray guns, hose, hose

connections and heaters).

FIRE

Static voltage is developed by airless spraying. The pump,

associated system, and object being sprayed must be grounded

to prevent static discharge sparks which could start a fire.

SERVICING

Before servicing, cleaning, or removal of any part, set trigger lock

on gun, and always shut off power source; then carefully release

pressure in fluid portions of the system.

181147

MAXIMUM INPUT 6.9 BAR (100 PSI)

- - - - - -

MAXIMUM OPERATING PRESSURE 206 BAR (3000 PSI)

Summary of Contents for PermaFlo 830







































































































Search results

Summary of Contents for PermaFlo 830

Reviews:

Related manuals for PermaFlo 830

Brands by name

Popular brands

Nordson PermaFlo 830, Customer Product Manual

Search results

Summary of Contents for PermaFlo 830

Reviews:

Related manuals for PermaFlo 830

Brands by name

Popular brands