Nordson PermaFlo 830 Customer Product Manual Download Page 14

Page: 14 / 102

Quick Reference

A 1-5

Part 1022914G03

2007 Nordson Corporation

Adhesives, Sealants, and Lubricants

Use these adhesives, sealants, and lubricants when servicing your pump.

Refer to

Solvent Chamber Fluid

for plunger lubrication information.

Part

Description

Quantity

900464

ADHESIVE, threadlocking (Loctite Removable 242)

900223

LUBRICANT, O-ring, Parker (Parker O-Lube), 4 oz

900349

LUBRICANT, TFE grease, 0.75 oz tube (MagnaLube-G)

Solvent Chamber Fluid

Solvent chamber fluid lubricates the plunger and reduces upper packing

wear.

Solvent chamber fluid is not shipped with the PermaFlo pump,

since the pump can be used with either water-based or solvent-based

coating materials. Refer to the

Solvent Chamber Fluid Guide

below for

application information.

Part

Description

248831

FLUID, type S, pump chamber, one quart

900255

FLUID, type K, pump chamber, one quart

140029

FLUID, type T, pump chamber, one quart

244854

FLUID, type-Q concentrate (2.6 fluid ounce, makes one gallon)

Solvent Chamber Fluid Guide

Use this chart to select the proper solvent chamber fluid to use with your

coating materials. For more information contact your Nordson

representative.

Solvent Type

Material

Application

Mixed aliphatic dimethyl

esters

Most commonly used fluid for solvent-based coatings.

Compatible with most solvent-based coatings.

Epoxidized soybean oil

Use with solvent-based coatings, except those containing

catalyzed alkyd urea.

Mixed propylene glycol

Most commonly used fluid for water-based coatings.

Requires no mixing, thinner and easier to pour than

Type Q.

Liquid anionic flocculant

mixed with distilled

water

Use with water-based coatings. Requires mixing with

distilled water. Thicker and harder to pour than Type T, but

provides better lubrication in tough applications.

Summary of Contents for PermaFlo 830







































































































Search results

Summary of Contents for PermaFlo 830

Reviews:

Related manuals for PermaFlo 830

Brands by name

Popular brands

Nordson PermaFlo 830, Customer Product Manual

Search results

Summary of Contents for PermaFlo 830

Reviews:

Related manuals for PermaFlo 830

Brands by name

Popular brands