Nordson Encore LT Page 49 Product Manual Download

Page: 49 / 92

Troubleshooting

5-1

Part 1604857-04

2014 Nordson Corporation

Section 5

Troubleshooting

WARNING:

Allow only qualified personnel to perform the following tasks.

Follow the safety instructions in this document and all other related

documentation.

WARNING:

Before making repairs to the controller or spray gun, shut off

system power and disconnect the power cord. Shut off the compressed air

supply to the system and relieve the system pressure. Failure to observe

this warning could result in personal injury.

These troubleshooting procedures cover only the most common problems.

If you cannot solve a problem with the information given here, contact your

contact Nordson technical support at (800) 433

−

9319 or your local Nordson

representative for help.

Controller Faults

Problem

Possible Cause

Corrective Action

1. Trigger LED blinks,

gun does not spray

Gun was triggered on when the

controller was powered up or

woken up

Release the trigger. Press the

Enable/Disable button to put the

controller to sleep, then press the

button again to wake it up.

Shorted trigger switch or cable

Check the gun cable and trigger

switch.

2. KV/

A display blinks,

no KV when gun is

triggered

Gun is shorted

Check gun cable, cable extension,

and gun power supply.

Summary of Contents for Encore LT





























































































Search results

Summary of Contents for Encore LT

Reviews:

Related manuals for Encore LT

Brands by name

Popular brands

Nordson Encore LT, Product Manual

Search results

Summary of Contents for Encore LT

Reviews:

Related manuals for Encore LT

Brands by name

Popular brands