manualshive.com logo in svg

Nordson EFD 2+2-XCH-V3, Operating Manual

Share
Download
Nordson EFD 2+2-XCH-V3 Operating Manual Download Page 56

Applicability of this Supplement

This supplement describes only the modifications and expansion of the PICO controller V3 when fieldbus 
parameterization is turned on. All other information on the PICO controller V3 is located in the main sections of this 
manual.
This supplement applies only to the PICO controller V3 2CH/4CH (hereinafter only referred to as the PICO controller) 
as of:

• 

 Hardware release 2.x and software release 3.x

 with activated fieldbus parameterization

The current software and hardware versions are shown under the PICO controller’s System Data menu option.
A PICO controller with activated fieldbus parameterization can be 
identified as follows:

•  The PICO controller has a “Fieldbus READY” label above the 

display

•   When switched on, an “F” is present in the upper right corner of 

the display.

PICO Controller 2+2-XCH-V3

56

www.nordsonefd.com   [email protected]

   +1-401-431-7000    Sales and service of Nordson EFD dispensing systems are available worldwide.

Summary of Contents for 2+2-XCH-V3





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands