background image

w w w . h a w k e y e e l e c t r o n i c s . c o m  

 

Make a copy of your original purchase receipt and staple it to this manual

You will need to present it in the rare occurrence that you need to send 
your product in for service.

 

 

Complete the information below and store this manual in a safe place.  

You can print additional copies of this manual from our website.

   

 

I

NFORMATION

To aid in maintenance and service, record the following: 

Date of Purchase: ___________________ 

Place of Purchase: _____________________________________ 

Date of Online Warranty Registration:  _____________________ 

Production Date Code : ________ 

(3 digit code located on the device housing)

 

 

LEGAL 

 

I

NFORMATION

Made in China.

 Tested to comply with FCC, CE & ROSH 

standards if applicable. Visit our website for compliance and 
warranty information. All Specifications and Prices Subject to 
Change Without Notice.   

NorCross Marine Products, Inc 

(P) 888-7NorCross (888-766-7276), 

(F) 407-370-6880, 

(E) [email protected] 

(I) www.norcrossmarine.com 

 

W

ARNING

© 2009 NorCross Marine Products Inc., All Rights Reserved. ALL 
unauthorized copying of the content of this document without the 
expressed written consent of NorCross Marine Products, Inc is 
strictly forbidden. 

 

Summary of Contents for D10DX.01T



















Reviews: