MODEL 72675 1250 LBS. CAPACITY POWERTRAIN LIFT/TABLE
SETUP • OPERATING • MAINTENANCE INSTRUCTIONS
PROFESSIONAL LIFTING EQUIPMENT
®
BEFORE USING THIS DEVICE, READ THIS MANUAL
COMPLETELY AND THOROUGHLY, UNDERSTAND ITS
OPERATING PROCEDURES, SAFETY WARNINGS AND
MAINTENANCE REQUIREMENTS. FAILURE TO DO SO COULD
CAUSE ACCIDENTS RESULTING IN SERIOUS OR FATAL
PERSONAL INJURY AND/OR PROPERTY DAMAGE.
The use of portable automotive lifting devices is subject to certain
hazards that cannot be prevented by mechanical means, but
only by the exercise of intelligence, care, and common sense. It
is therefore essential to have owners and personnel involved in
the use and operation of equipment who are careful, competent,
trained, and qualified in the safe operation of the equipment and
its proper use. Examples of hazards are dropping, tipping, or
slipping of motor vehicles or their components caused primarily by
improperly securing loads, overloading, off-centered loads, use on
other than hard level surfaces, and using equipment for a purpose
for which it was not designed.
It is the responsibility of the owner to make sure all personnel read
this manual prior to using this device. It is also the responsibility of
the device owner to keep this manual intact and in a convenient
location for all to see and read. If the manual is lost or not legible,
contact Norco Industries, Inc. for a free replacement. If the operator
is not fluent in English, the product and safety instructions shall be
read to and discussed with the operator in the operator’s native
language by the purchaser/ owner or his designee, making sure
that the operator comprehends its contents.
WARRANTY
This product is covered by a Limited Lifetime Warranty. For details
see the back cover of Norco’s product catalog.
IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING
WARNING
• Adequately support the vehicle before starting repairs.
Consult the in-ground or above-ground lift manufacturer for
the recommended support procedure and under hoist support
stand locating points.
• Support the engine with a stand before unbolting the
transmission from the engine.
• Do not use the lift table for removal of fuel tanks without using
the approved Norco Model 72508 Fuel Tank Saddle. Fuel tanks
must be emptied before removal, installation or transportation.
• Inspect the lift table before each use. Do not use the lift table
if it is damaged, altered, modified, in poor condition, leaking
hydraulic fluid, leaking air, or unstable due to loose or missing
hardware. Take corrective action before using the lift table.
• Do not use lift table beyond its rated capacity. Do not lift or
support the vehicle with this lift table.
• Do not exceed 120 P.S.I. input air pressure.
• Use only on a hard level surface.
• Be sure setup is stable and secure. Use this lift table only with
adapters and load restraints provided by Norco. Use of this lift
table is limited to the removal, installation and transportation (in
the lowered position) of transmissions, transfer cases, engines,
rear ends and leaf springs. Center load on saddle. Consult the
vehicle manufacturer for the component’s center of balance.
Off-center loads can cause lift failure and/or loss of load.
• Do not lift or move a load that has a center of gravity extending
beyond the front wheels.
•
Never remove, install or transport any component without first
tightly securing it to the universal saddle, adapters or fuel tank
saddle using the load restraints provided.
• Do not move the lift table when the load is raised. Always lower
the load completely before moving, storing or using as a work
table.
• Do not stand under a load that is raised by the lift table.
• No alterations shall be made to this lift table and use only with
factory approved adapters.
SETUP
1.
Refer to the exploded view parts drawing for identification,
location and position of parts.
2.
Remove the red fill plug in the top of the air/hydraulic foot pump
and replace it with the black vented fill plug.
3.
Install the air quick disconnect of your choice at the rear of the
hydraulic foot pump and connect the shop air line.
4.
The powertrain lift table is equipped with a universal saddle.
Optional automotive transmission adapters and fuel tank saddle
are available. The universal saddle must be removed when using
other optional Norco transmission adapters and the fuel tank
saddle.
Note: Revision letters (A, B, C, D etc.) after model numbers have been omitted as they do not affect the setup,
operating and maintenance instructions of a particular jack unless otherwise noted.
