Nokia NPM-2NX Troubleshooting Manual Download Page 62

Page: 62 / 66

NPM-2NX

Troubleshooting

CCS Technical Documentation

Page 62

Nokia Corporation

Issue 1 07/02

• Tuning results are only visible after unsuccessful tuning with auto-tune proce-

dure

• This tuning has done simultanously with AFC-tuning

If LP and AMP2 filter tuníngs fail it might be due to:

• Problems with lower band signal path (synthetizer etc.)

• VCTCXO component can be broken

• Safari can be broken or solder joints

UB RX AGC tuning

• UB TDMA minimum gain (around 0 dB), measured when lna is switched off

• UB LNA gain step, measured when lna is switched on. Result is gain difference

between lna on and off (around 20 dB)

• If UB TDMA minimum gain is lower than -2 further analysis is needed. Result

32752 means that the signal doesn't go through RX chain at all or it has a lot of
attenuation.

If it fails there can be following problems:

• Rx chain is totally deaf or some gain is missing, start receiver troubleshooting

LB RX AGC tuning

• LB TDMA minimum gain (around 2 dB), measured when lna is switched off

• LB LNA gain step, measured when lna is switched on. Result is gain difference

between lna on and off (around 20 dB)

• If LB TDMA minimum gain is lower than -2 dB, further analysis is needed. Result

32752 means that the signal doesn't go through RX chain at all or it has a lot of
attenuation.

If it fails there can be following problems:

• Rx chain is totally deaf or some gain is missing, start receiver troubleshooting

TDMA TX tunings

If some TX tunings fails, start always TX troubleshooting!

TX IQ (TxIq)

Summary of Contents for NPM-2NX



































































Search results

Summary of Contents for NPM-2NX

Reviews:

Brands by name

Popular brands

Nokia NPM-2NX, Troubleshooting Manual

Search results

Summary of Contents for NPM-2NX

Reviews:

Brands by name

Popular brands