background image

GB 8

GENERAL INFORMATION ABOUT THE MEDIAMASTER

Throughout this manual you will notice that the everyday operation of your Media-
master is based on a series of user friendly on-screen displays and menus. These
menus will help you get the most from your Mediamaster, guiding you through instal-
lation, channel selection, viewing and many other functions.

All functions can be carried out using the buttons on the remote control, and some of
the functions can also be carried out using the buttons on the front panel.

Please be aware that new software may change the functionality of the Mediamaster.

Should you experience any difficulties with the operation of your Mediamaster, please
consult the relevant section of this manual, including the Problem Solving, or alterna-
tively call your dealer or a customer service adviser.

Nokia Mediamaster 220 S is adapted to Viasat requirements for digital satellite TV re-
ceivers. The receiver is intended for reception of Viasat’s bouquet of channels and in-
teractive services, and for reception of free-to-air and encrypted channels from the Thor,
Sirius, Hotbird and Astra satellites. Software is updated automatically via the Sirius
satellite. 

A valid Viasat smart card must be inserted in the embedded Viaccess™

card reader to be able to use the reciver.

• Allow 10 cm space around the Mediamaster for sufficient ventilation.

• Do not cover the Mediamaster’s ventilation openings with items such as news-

papers, table-cloths, curtains etc.

• Do not place the Mediamaster on top of a unit that emits heat.

• Do not place naked flame sources, such as lighted candles, on the Mediamaster.

• Use a soft cloth and a mild solution of washing-up liquid to clean the casing.

• Do not expose the Mediamaster to dripping or splashing liquids.

• Do not place any objects filled with liquids, such as vases, on the Mediamaster.

• To give your Mediamaster an extra protection, e.g. at a thunderstorm, we rec-

ommend that you connect it via an external surge protection device.

• Do not connect or modify cables when the Mediamaster is plugged in.

• Do not remove the cover.

• Do not allow the unit to be exposed to hot, cold or humid conditions.

• Service should be carried out only at a Nokia Authorised Service Centre.

• Please note that the only way to isolate the Mediamaster completely from the

mains supply is to unplug the mains cable!

IMPORTANT! Read this before using the Mediamaster!

Summary of Contents for Mediamaster 220S





































Reviews: