manualshive.com logo in svg

Nokia Alcatel-Lucent OXO Connect Compact, Installation Manual

Share
Download
Nokia Alcatel-Lucent OXO Connect Compact Installation Manual Download Page 143

8.7.2.2 Jumpers

The jumper in a gray background is factory installed.

Operation Mode

Stand Alone

Associated UA Set

To  configure  the  V24/CTI  Interface  Module,  open  the  device  with  the  2  screws  located  under  the
module.

If the jumper is positioned for "stand-alone" operation, an associated set cannot work.

If  the  jumper  is  positioned  for  "associated  UA  set"  operation,  the  associated  set  is  mandatory,  the
Interface Module cannot work without it.

8.7.3 External connections

8.7.3.1 V24/CTI Interface Module Connection

The V24/CTI Interface Module is connected as follows:

Chapter 

8

Device commissioning

8AL91217USAA - Ed. 01  - July 2018 - Installation Manual

143/216

Summary of Contents for Alcatel-Lucent OXO Connect Compact

























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands