manualshive.com logo in svg

Nokia 7705, Installation Manual

Share
Download
Nokia 7705 Installation Manual Download Page 66

7705 SAR-Hm and 7705 SAR-Hmc Overview

66

SAR-Hm and SAR-Hmc Chassis Installation Guide

© 2022 Nokia. Nokia Confidential Information

Use subject to agreed restrictions on disclosure and use.

3HE 17810 AAAA TQZZA 

 

3.2.1.7

Main and Diversity Antenna Connectors

The 7705 SAR-Hm and 7705 SAR-Hmc have two subminiature version A (SMA) 
(female) connectors on the front of the chassis that are designed for external Main 
and Diversity antennas. See 

Cellular Components

 for more information. See also 

Direct-mounting the Indoor LTE Omni-directional Antenna

 and 

Installing and 

Grounding Outdoor Cellular Antennas

.

3.2.1.8

GPS Antenna Connector

The 7705 SAR-Hm and 7705 SAR-Hmc have an integrated Global Navigation 
Satellite System (GNSS) SMA (female) connector that is used for an external 
GNSS/GPS antenna.

See 

GNSS Components

 for more information.

3.2.1.9

WLAN Connector

The 7705 SAR-Hm has a reverse polarity RP-SMA (female) WLAN connector that is 
used for a WiFi antenna that supports a 2.4 GHz/5 GHz, IEEE 802.11b/g/n WLAN 
interface.

See 

WLAN Components

 for more information. Installation of the WiFi antenna is 

described in 

Direct Mounting an Indoor WiFi Antenna

 and 

Installing and Grounding 

WLAN Outdoor Antennas

.

3.2.1.10

Chassis Grounding

The 7705 SAR-Hm and 7705 SAR-Hmc have one designated grounding point on the 
front of the chassis. See 

Grounding the Chassis

 for more information.

Note: 

Both the 7705 SAR-Hm and 7705 SAR-Hmc Alarms port inputs have 100k Ohm 

pull-up resistors to 3.3V.

Summary of Contents for 7705





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands