manualshive.com logo in svg

Nokia 500i, Installation Manual

Share
Download
Nokia 500i Installation Manual Download Page 36

2

  Performing the Initial Configuration

36

 

Nokia 500i Installation Guide

Figure 4  Power Switch Location on the Nokia 500i

To connect the power

1.

Connect the power cord securely into the power socket on the back of the 
gateway. 

2.

Plug the other end of the cord into a three-wire grounded power strip or 
wall outlet.

3.

Press the power supply switch to the On position to provide power.

The fan unit turns on when you press the power switch. Verify that the fans 
are running after you press the switch. 

Check the power LED on the front panel of the gateway (the Nokia logo) to 
ensure that the power supply is operating correctly. The power LED should be 
illuminated.

If the power supply fans are not running, or if the power LED is not 
illuminated:

!

Check the power supply cord to make sure it is properly connected.

!

Make sure the power supply switch is on.

00500

Power plug

Power switch

Summary of Contents for 500i

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands