manualshive.com logo in svg

Nokia 500i, Installation Manual

Share
Download
Nokia 500i Installation Manual Download Page 23

Installing the Nokia 500i Gateway

Nokia 500i Installation Guide

 

23

Installing the Nokia 500i Gateway

The Nokia 500i gateway is a two-rack-unit appliance that incorporates a 
serviceable slide-out tray into the chassis design. The front panel of the Nokia 
500i gateway has two I/O slots. A 6U PMC carrier is provided for the I/O 
slots. Each 6U PMC carrier supports two PMC network interface cards 
(NICs) for a total of four NICs.

Note
The 6U PMC carrier on the Nokia 500i gateway is not hot swappable. You 
must turn off power to the system before replacing NICs on the Nokia 
500i gateway.

The front panel of the 500i gateway also contains:

!

Two PCMCIA slots

!

One console port

!

One serial port

!

One four-port Ethernet management interface

The Nokia 500i gateway is designed to meet other mid- to high-end 
availability requirements, including port density for connections to redundant 
internal, external, DMZ, and management networks. You can purchase the 
500i gateway with either AC or DC (NEBS) redundant power supplies. In 
addition, the Nokia 500i gateway provides N + 1 cooling.

Grounding the Nokia 500i Gateway

To ground the 500i gateway

1.

Locate and remove from the package the #6 ring tongue lugs and kep 
nuts.

2.

Attach a 10 AWG or 12 AWG insulated grounding cable to the lugs.

Summary of Contents for 500i

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands