The NodOn
®
Smart Plug + Metering allows to control (Power ON
or Power OFF) an electrical appliance plugged on it: bedside lamp,
electrical heater, coffee machine, etc. Once set up (see the set
up procedures below), the NodOn
®
Smart Plug can be controlled
by different EnOcean
®
compliant emitters (wall switch, remote
controller, sensor, window handle, card switch, etc.).
Check the compliant emitters list below.
Thanks to build-in Metering features, the Smart Plug can meter
Instantaneous Power (W) and Accumulated Energy (Wh), between
two buffer's reset.
INSTALLATION
Thanks to an innovative design, the Smart Plug can be mounted on
the power outlet in either side, head up or head down.
1
Plug the NodOn
®
Smart Plug on your power outlet.
2
Plug the electrical appliance, you want to control, on the NodOn
®
Smart Plug.
3
The Smart Plug allows to switch ON (Power ON) or switch OFF
(Power OFF) the electrical appliance you want to control.
Switching ON or OFF can be done through the Smart Plug local
button, or any kind of emitter paired to the Smart Plug (check the
next steps of the user guide).
If the electrical appliance (ex.: bedside lamp) has an ON/OFF button, make sure it’s positioned
on “ON”, in order that the power ON of the appliance by the Smart Plug will switch ON the lamp.
SMART PLUG MODES
LOCAL CONTROL
The Smart Plug can be switched ON or OFF locally, through a short
press on the local button. By default, the Smart Plug is switched
ON when the LED is green, OFF when the LED is OFF.
PAIRING MODE
Press on the Smart Plug button during 2 seconds until the LED
becomes red. Release the button, the LED will then glow in red. The
Smart Plug is in “Pairing mode”.
To pair an emitter, follow the “Pairing procedures”. To confirm that
the pairing is OK, the LED will blink in green.
If the LED blinks orange during “Pairing mode”, it means that the
memory of the Smart Plug is full, or that no emitter has been paired
during the process.
In case of full memory, please unpair an emitter before being able
to pair a new one.
FACTORY RESET
To perform a factory reset, press on the Smart Plug button during
5 seconds until the LED becomes orange. Release the button, the
LED will blink red/green.
The factory reset will remove all the emitters from the Smart Plug
memory, and set all the parameters of the Smart Plug to default
value.
Factory Reset clears Energy (Wh) buffer as well.
PAIRING PROCEDURES
Wall Switch, Remote Controller, etc.
EnOcean
®
Type “Rocker Switch” (EEP: F6-02-01)
To pair this type of emitter to the Smart Plug:
1
Put the Smart Plug in “Pairing mode”.
2
Press any button of the emitter. The button pressed during the
pairing process is the button which will switch ON the Smart Plug.
The opposite button will switch OFF the Smart Plug.
The other buttons of the emitter will not be able to control the
Smart Plug.
Pairing Mode
Usage
Button paired during
“Pairing mode”
Button pressed on
the emitter
Smart Plug state
I
I
ON
O
OFF
O
O
ON
I
OFF
P
P
ON
M
OFF
M
M
ON
P
OFF
To unpair this emitter:
1
Put the Smart Plug in “Pairing mode”.
2
Press any button of the emitter
The emitter can’t control the Smart Plug anymore.
Key Card Activated Switch
EnOcean
®
Type “Key Card Activated Switch” (EEP: F6-04-01)
To pair this type of emitter to the Smart Plug:
1
Put the Smart Plug in “Pairing mode”.
2
Insert or remove the card from the reader. The movement of
the card done during the pairing process is the movement which
will switch ON the Smart Plug. The opposite movement will switch
OFF the Smart Plug
3
To initialize the Smart Plug, insert and remove (or remove and
insert) the card.
Pairing Mode
Usage
Movement done during
« Pairing mode »
Card position
Smart Plug state
INSERT
INSERTED
ON
REMOVED
OFF
REMOVE
REMOVED
ON
INSERTED
OFF
To unpair this emitter:
1
Put the Smart Plug in “Pairing mode”.
2
Insert or remove the card.
The emitter can’t control the Smart Plug anymore.
Window Handle
EnOcean
®
Type “Window Handle” (EEP: F6-10-00)
To pair this type of emitter to the Smart Plug:
1
Put the Smart Plug in “Pairing mode”.
2
Make the relevant movement with the handle according to your
need. Check below table.
Note: “Bottom hung” and “Open” position are identically considered
Pairing Mode
Usage
Movement done during
« Pairing mode »
Handle position Smart Plug state
OPEN or BOTTOM HUNG
OPENED or
BOTTOM HUNG
ON
CLOSED
OFF
CLOSE
CLOSED
ON
OPENED or
BOTTOM HUNG
OFF
To unpair this emitter
1
Put the Smart Plug in “pairing mode”.
2
Make any kind of movement with the handle.
The emitter can’t control the Smart Plug anymore.
Opening sensor
EnOcean
®
Type “Magnetic Contact” (EEP: D5-00-01)
To pair this type of emitter to the Smart Plug:
1
Put the Smart Plug in “Pairing mode”.
2
Press on the “learning” button of the opening sensor. The
position (close or far) of the magnet from the sensor when the
“learning” button is pressed is the position which will switch ON
the Smart Plug. The opposite position will switch OFF the Smart
Plug. Check the table below.
Pairing Mode
Usage
Magnet position when the
« Learning » button is
pressed
Magnet position Smart Plug state
CLOSE
CLOSE
ON
FAR
OFF
FAR
FAR
ON
CLOSE
OFF
To unpair this emitter:
1
Put the Smart Plug in “pairing mode”.
2
Press on the “learning” button
The emitter can’t control the Smart Plug anymore.
Motion sensor
EnOcean
®
Type “PIR Sensor” (EEP: A5-07-01 / A5-07-02 / A5-
07-03 / A5-08-01 / A5-08-02 / A5-08-03)
To pair this type of emitter to the Smart Plug:
1
The status of the Smart Plug (ON or OFF) chose before put in
“pairing mode” will be associate to a presence detection
2
Put the Smart Plug in “pairing mode”.
3
Press the “learning” button of the presence sensor.
When a presence is detected, the Smart Plug will be in the state
(ON or OFF) defined at step 1.
When no presence is detected, the Smart Plug will be in the
opposite state. Check the table below.
Pairing Mode
Usage
Smart Plug state before
“pairing mode”
Sensor status
Smart Plug state
ON
PRESENCE
ON
NO PRESENCE
OFF
OFF
NO PRESENCE
ON
PRESENCE
OFF
To unpair this emitter:
1
Put the Smart Plug in “pairing mode”.
2
Press on the “learning” button.
The emitter can’t control the Smart Plug anymore.
Open
Bottom hung
Close
Open
Bottom hung
Open
Bottom hung
learning
close
far
Power supply : 230V AC - 50Hz
Self-consumption <1W
Max. power : - 3000W continuous (Resistive load)
- 3500W temporary (Resistive load)
Metering of Instantaneous Power (W) and accumulated Energy (Wh)
Center radio frequency : 868.3 MHz
Occupied frequency band : 868.0 to 868.6 Mhz
RF power Max : +3dBm
Indoor range: 30m
Operational temperature: -10°C / 50°C
IP20
Memory capacity : 24 emitters
EEP (Profil EnOcean
®
): D2-01-0B
Dimensions: L 51mm x l 36mm x h 104mm
Weight: 137g
Warranty: 2 years
USER GUIDE
SMART PLUG
METERING
Smart Plug Type E
Reference: ASP-2-1-01
Smart Plug Schuko
Reference: ASP-2-1-11