CONTENTS:
OPERATION MANUAL
BATTERY INFO (Consult battery charge manual)
REMOTE CONTROL OPERATION:
CARE AND MAINTENANCE
Read this instruction manual before
playing with your Remote Control
1 Radio-controlled vehicle
1 Remote control
1 USB port power cord
2 x AAA 1.5V batteries
1 x Rechargeable Battery
MANUFACTURATED BY:
TOY PLUS (FAR EAST) LIMITED
Unit 09 9/F, Houston Centre,
63 Mody Road, Tsim Sha Tsui East,
KL, Hong Kong (852) 2366 8480
MADE IN CHINA.
VEHICLE
The vehicle requires 1 rechargeable battery.
To charge battery:
1. Use a screwdriver to take off the battery lid in the bottom of the vehicle.
2. Remove battery completely.
3. Connect the battery adapter to the USB port power cord. Connect the USB port power cord to the electronic
USB plug (Only 5V output).
4. Once the battery is charged, disconnect the cord, place and set the battery inside the compartment.
fig.2
fig.1
fig.3
fig.4
REMOTE CONTROL
Control requires 2 x AAA 1.5V /LR03/R03 batteries (included).
OPEN
CLOSE
1. Switch “ON/OFF” interrupter in OFF position.
2. Use a screwdriver to open the battery compartment lid (fig 5), insert batteries with the
right polarity (fig. 6).
3. Return the lid and close with the screwdriver. (fig. 7).
Forward
Backward
Right
Special Action
Button
Left
NOTE: The indicator light on the
charging cable flashes during charging
and turns off when the battery is fully
charged.
fig.5
fig.7
fig.6
AAA
AAA
AAA
AAA
2x
IMPORTANT INFORMATION
Battery installation or replacement should be done by an adult. Use only recommended batteries as specified on
packaging and this instruction manual. Make sure to place batteries with the correct polarity as indicated. Don’t mix
new and used batteries. Don’t mix different battery types: alkaline, standard, rechargeable. Non-rechargeable
batteries are not be recharged. Always remove rechargeable battery prior to charge (in case they are removable). It’s
necessary to remove used batteries from the toy as they might affect its performance. Power ports should not be put in
short circuit.
ITEM NO: 21011
4 . 8 V N i - M H 5 0 0 m A h
2 x 1 . 5 V R 0 3 ( A A A )
4 . 8 V N I - M H
5 0 0 m A h
4.8V NI-MH
500 mAh
FCC COMPLIANCE
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
XCORPION
XCORPION
XCORPION
XCORPION
XCORPION
XCORPION
XCORPION
