Nintendo Ultra64 Programmer'S Manual Download Page 41

Page: 41 / 331

Revision 1.0

Execution Pipeline

Execution Pipeline

RSP Block Diagram

The RSP execution pipeline is illustrated in Figure 2-8.

The scalar unit of the RSP has a five stage pipeline:

Instruction Fetch. During this stage, two instruction are
fetched and decoded, dual-issuing, if possible.

Execute. For computational operations, the result is
calculated; for loads/stores/branches, the address is
calculated.

Data Fetch. For loads, the data is fetched; store data is
stored.

Write Back. Results are written back to registers.

The vector unit also has a five stage pipeline:

Instruction Fetch. Nothing happens in the VU during
this stage.

MUL

Multiply. During this stage, computational operations
are computed. Reciprocal operations begin
table-lookup.

ACC

Accumulate. Additional computation is performed.
Reciprocal operations perform table-lookup.

Write Back. Minor computations and writing of data to
vector registers.

Summary of Contents for Ultra64












































































































































































































































































































































Search results

Summary of Contents for Ultra64

Reviews:

Related manuals for Ultra64

Brands by name

Popular brands

Nintendo Ultra64, Programmer'S Manual

Search results

Summary of Contents for Ultra64

Reviews:

Related manuals for Ultra64

Brands by name

Popular brands