Nilfisk-Advance SC401 17 B Service Manual Download Page 163

Page: 163 / 173

163

Service Manual – SC401, SCRUBTEC 344

40 - Recovery System

Vacuum Motor Current Draw Test

WARNING:

This procedure must be performed by qualified personnel only.

1 Disconnect the vacuum hose to the squeegee

Remove the vacuum grid with the float, after the test reinstall it.

3 If present, drain the recovery tank, then lift it

4 Apply the amp clamp (A) on the positive cable (grey) of the vacuum harness (B)

5 (If equipped) Turn the ignition key to “I”

6 Press the Main button

to start the machine

7 Activate the vacuum by pressing the Vacuum system button

to full power (Led on)

8 Activate the vacuum and check that the current draw of the vacuum motor is between 11 and 12 at 24V

Stop the vacuum

Remove the amp clamp (A)

If the amperage is higher, perform the following procedures to detect and correct the abnormal

amperage:

◦

Remove the vacuum system motor (see the “

Container and vacuum motor disassembly/assembly

”

paragraph), and check the condition of all its components

If the above-mentioned procedures do not produce the correct readings for the vacuum system motor

amperage, the motor must be replaced (see the “

Container and vacuum motor disassembly/assembly

”

paragraph)

Figure 5:

Summary of Contents for SC401 17 B














































































































































































Search results

Summary of Contents for SC401 17 B

Reviews:

Related manuals for SC401 17 B

Brands by name

Popular brands

Nilfisk-Advance SC401 17 B, Service Manual

Search results

Summary of Contents for SC401 17 B

Reviews:

Related manuals for SC401 17 B

Brands by name

Popular brands