Nilfisk-Advance SC401 17 B Service Manual Download Page 126

Page: 126 / 173

126

Service Manual – SC401, SCRUBTEC 344

30 - Solution System

Adjusting of Detergent Concentration in the Washing Water

The system for mixing the detergent in the washing water is automatically activated when the brush is

running

The percentage of detergent added to the washing water is set to 0,25%, to change the setting perform

press the Solution button

for more than two seconds to perform the adjustment The set percentage

depends on the relevant LED turned on, on the battery symbol

Figure 1:

To change the setting or to reset it (all LEDs off), press Solution button

to set the percentage

Note:

The setting is stored 3 minutes after releasing all push-buttons. Detergent percentage setting

is stored into memory, even if the machine is switched off.

Summary of Contents for SC401 17 B














































































































































































Search results

Summary of Contents for SC401 17 B

Reviews:

Related manuals for SC401 17 B

Brands by name

Popular brands

Nilfisk-Advance SC401 17 B, Service Manual

Search results

Summary of Contents for SC401 17 B

Reviews:

Related manuals for SC401 17 B

Brands by name

Popular brands