Nilfisk-Advance SC401 17 B Service Manual Download Page 121

Page: 121 / 173

121

Service Manual – SC401, SCRUBTEC 344

24 - Electrical System (Cord)

Functional Description

The machine electrical system is composed of the following components:

• Power supply cable with dedicated mains plug

• Main switch (SW1): turns the machine on and off

• Main machine controller (EB1): receives the commands from the User interface controller (EB2) and

powers directly all the machine services

• User interface controller (EB2): it is responsible for the user interface, as it contains all control

buttons and the indicator LEDs, and is connected to the two Operator presence sensors (S1, S2) on the

handlebars All information from and for the user is exchanged with the Machine main controller (EB1)

via I2C protocol

Summary of Contents for SC401 17 B














































































































































































Search results

Summary of Contents for SC401 17 B

Reviews:

Related manuals for SC401 17 B

Brands by name

Popular brands

Nilfisk-Advance SC401 17 B, Service Manual

Search results

Summary of Contents for SC401 17 B

Reviews:

Related manuals for SC401 17 B

Brands by name

Popular brands