manualshive.com logo in svg

Nilfisk-Advance Micromatic M17B, Service Manual, Page: 39 / 52

Share
Download
Nilfisk-Advance Micromatic M17B Service Manual Download Page 39

ELECTRICAL SYSTEM

SERVICE MANUAL

ENGLISH

Micromatic

TM

 M17B - Micromatic

TM

 M17E

9097091000(1)2007-06

37

Battery charging with battery charger installed on the machine

Connect the battery charger cable (27) to the electrical mains (the mains voltage and frequency must be compatible with the 

battery charger values: see the battery charger Manual).

NOTE

When the battery charger is connected to the electrical mains, all machine functions are automatically cut off.

The green warning light (34) flashes when the battery charger is charging the batteries.

When the green warning light (34) stays on, the battery charging cycle is over.

When the battery charging is over, disconnect the battery charger cable (27) from the electrical mains and wind it round its 

housing on the machine.

NOTE

For further information about the battery charger operation (33), see the relevant Manual.

Reset

For lead (WET) batteries only:

Check for the correct level of electrolyte inside the batteries (50). If necessary, add distilled water through the caps.

Close all the battery caps.

If necessary, clean the upper surface of the batteries. 

Grasp the recovery water tank (A) in the area (B) and lay it on the machine as shown in the figure, then connect the 

vacuum hose (C) to the tank, and bring it back to its original position.

Connect the vacuum hose (29) to the squeegee (17).

Close the cover (12).

Now the machine is ready to be used.

A

B

C

D

E

S301210

11.

12.

13.

14.

•

•

•

•

•

•

15.

Summary of Contents for Micromatic M17B





















































Reviews:

No comments