manualshive.com logo in svg

Nikon Total Station DTM-322, Instruction Manual, Page: 93 / 185

Share
Download
Nikon Total Station DTM-322 Instruction Manual Download Page 93

Total Station DTM-322 Instruction Manual     

79

Applications     

4

Sample output records through COM port

When the Ext.Comm field is set to NIKON:
TR PN:    PT8 SD:000066626 HA:003856010 VA:008048500 HT:0000061757
(TR PN: point name SD HA VA HT; when ACK is returned, PN is incremented.)

When the Ext.Comm field is set to SET:
0006662 0804806 0394324 97
(SD VA HA Chk-SUM)

Measuring Offsets

Measuring taped offsets

1.

To enter the taped offset function, press 

[1]

 or 

select 

Tape

 in the Offset menu. 

If you have not taken a distance measurement 
before entering this function, a temporary 
measurement screen appears.

2.

Sight the target and press 

[MSR1]

 or 

[MSR2]

.

3.

Enter offset distances from the measured point. 
Use 

[^]

 or 

[v]

 to move to the appropriate offset 

field.

Left (-)

In (-)

Up (+)

Out (+)

Down (-)

Right (+)

Summary of Contents for Total Station DTM-322


























































































































































































Reviews:

No comments