manualshive.com logo in svg

Nikon NPL-632, Instruction Manual

The Nikon NPL-632, a versatile and feature-packed camera, is an excellent choice for photography enthusiasts. Capture stunning images with ease using this top-notch device. Ensure optimal utilization of its functions by referring to the comprehensive Instruction Manual available for free download exclusively at manualshive.com.

Share
Download
background image

3

     Getting Started

52

     Field Station NPL-632 Instruction Manual

5.

Press 

[1] 

to open the Control Job screen.

6.

Press the 

Yes

 softkey.

For more information, see 

Creating a control job, 

page 51

.

Measuring Distances

Sighting a prism reflector

C

WARNING – 

Never look at the sun through the telescope. If you do, you may damage or lose 

your eyesight.

Sight the telescope to see crosshairs at the center of the prism 
reflector. 

When a reflected lightwave is detected, the signal level is 
indicated.

When you enter a point name or number, the system searches in the current job first. If the point is not found in 
the current job, the search is automatically extended to the control job. If the point is found in the control job, the 
selected point is copied to the current job as a UP record.

For information on how to assemble the prism reflector, see 

Setting Up the Prism Reflector, page 22

.

Sighting a single prism

Sighting a tiltable 

single prism

Summary of Contents for NPL-632















































































































































































































Reviews:

No comments

Related manuals for NPL-632

Magtrol 6530 User Manual preview
6530
Brand: Magtrol Pages: 83
Nellcor OxiMax N-550 Operator'S Manual preview
OxiMax N-550
Brand: Nellcor Pages: 104
OHAUS Defender T24PE Instruction Manual preview
Defender T24PE
Brand: OHAUS Pages: 32
Oldham OX 2000 Use And Maintenance preview
OX 2000
Brand: Oldham Pages: 34
Raycus RFL-A1000D Manual preview
RFL-A1000D
Brand: Raycus Pages: 40
RaycoWylie i4000 Calibration Instructions Manual preview
i4000
Brand: RaycoWylie Pages: 31
Yamaha Arius YDP-160 Midi Data Format preview
Arius YDP-160
Brand: Yamaha Pages: 6
Flowmetrics 922-MFC Installation And Operating Instructions Manual preview
922-MFC
Brand: Flowmetrics Pages: 102
THORLABS PM10-10 Operation Manual preview
PM10-10
Brand: THORLABS Pages: 21
Circutor Wibeee Max Instruction Manual preview
Wibeee Max
Brand: Circutor Pages: 48
Hanna Instruments HI 9147 Instruction Manual preview
HI 9147
Brand: Hanna Instruments Pages: 2
Zero 88 DMX DeBug Manual preview
DMX DeBug
Brand: Zero 88 Pages: 32
Halo Photonics Stream Line Pro Hardware And Software Manual preview
Stream Line Pro
Brand: Halo Photonics Pages: 45
Dive Perfect Stubby LED-1500 User Manual preview
Stubby LED-1500
Brand: Dive Perfect Pages: 4
Zircon MultiScanner HD800 OneStep Instructions preview
MultiScanner HD800 OneStep
Brand: Zircon Pages: 2
HERON dipper-T Operating/Maintenance Instructions & Warranty preview
dipper-T
Brand: HERON Pages: 2
Kawai ANYTIMEX3 Owner'S Manual preview
ANYTIMEX3
Brand: Kawai Pages: 166
Kalse TRIAXIAL ELF SK-8301 Instruction Manual preview
TRIAXIAL ELF SK-8301
Brand: Kalse Pages: 2

Brands by name

Popular brands

Load more brands