Nikon NPL-302 Series Instruction Manual Download | Manualshive

Page: 8 / 234

background image

Safety

viii

Pulse Laser Station NPL-302 Series Instruction Manual

Warnings and Cautions

The following conventions are used to indicate safety instructions:

C

Warning –

Warnings alert you to situations that could cause death or serious

injury.

C

Caution –

Cautions alert you to situations that could cause injury or property

damage.

Always read and follow the instructions carefully.

Warnings

Before using the instrument, read the following warnings and follow the
instructions that they provide:

C

Warning –

Never look at the sun through the telescope. If you do, you may

damage or lose your eyesight.

C

Warning –

NPL-302 series instruments are not designed to be

explosion-proof. Do not use the instrument in coal mines, in areas
contaminated with coal dust, or near other flammable substances.

C

Warning –

The NPL-302 series instrument is a Class 1 laser instrument. The

laser beam is hazardous to the eyes and the body. Do not sight the instrument
on the face or body of a person. If you suspect an injury caused by exposure
to the laser beam, seek medical advice immediately.
If the instrument housing is open and the instrument is turned on, the laser
emits a beam stronger than the Class 1 safety level.

C

Warning –

Never disassemble, modify, or repair the instrument yourself. If

you do, you may receive electric shocks or burns, or the instrument may catch
fire. You may also impair the accuracy of the instrument.

«
...
6
7
8
9
10
...
»

Summary of Contents for NPL-302 Series











































































































































































































































Reviews:

No comments

Related manuals for NPL-302 Series

Brand: ParTech Pages: 14

Brand: Aaronia Pages: 47

Brand: E+E Elektronik Pages: 40

Brand: QMI Pages: 54

Bass Master Rockabilly

Brand: K&K Sound Pages: 2

Brand: Sensia Pages: 16

Brand: janitza Pages: 48

ProcessMaster FEP630 series

Brand: ABB Pages: 92

Brand: National Instruments Pages: 15

Brand: Bamo Pages: 17

HYDROMETTE HB 30

Brand: GANN Pages: 65

Brand: Leica Pages: 2

DIGIMET E30 Preset

Brand: MATO Pages: 20

DigiFlow 6710M-22

Brand: Savant Pages: 3

Brand: Benetech Pages: 16

Brand: RADWAG Pages: 12

Brand: Chauvin Arnoux Pages: 12

Brand: ICP DAS USA Pages: 340

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands