Nikon NPL-302 Series Instruction Manual Download

Page: 61 / 234

Getting Started

Pulse Laser Station NPL-302 Series Instruction Manual

[MODE]

key

30.1

Use the

[MODE]

key to change the keyboard mode for the current screen.

Changing input mode while entering points or codes

When the cursor is in a point (PT) or code (CD)
field, press

[MODE]

to change the input mode

between alphanumeric (

) and numeric (

The input mode indicator in the status bar changes
to show the current input mode.

Quick code measurement mode

To activate Quick code measurement mode,
press

[MODE]

in the BMS.

The PT field shows the default point name.

Press any numeric key (

[0]

through

[9]

) to start

measuring and recording points.

A list of the numeric keys and their assigned
feature codes appears on the right side of the
screen.

For example, when you press

[6]

, the code

assigned to 6 is selected, and the instrument
starts a measurement.

When the cursor is in a height (HT) field, only numeric input mode is available.
Pressing

[MODE]

has no effect when the cursor is in a HT field.

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands