Nikon NPL-302 Series Instruction Manual Download

Page: 227 / 234

Error Messages

Pulse Laser Station NPL-302 Series Instruction Manual

207

Caution –

If the existing point is a UP, CC, or MP record, and is not referred

by ST or BS, then it will be overwritten by the uploaded record. No error
message appears.

PT MAX16 chars

103.3

The uploaded data contains a PT with a name or number that is longer than 16
digits.

Press any key. Then check the specified line in the data.

XYZ OVERRANGE

103.4

The uploaded data contains a coordinate that is longer than 13 digits.

Press any key. Then check the specified line in the data.

Data

10.4

Can't Edit Current ST

104.1

You have tried to edit the current ST.

Note –

You cannot edit the current ST. However, old ST records can be edited. No

recalculation can be performed on the instrument.

Press any key to return to the code/layer name input screen.

Can't Edit ST/BS refer to this PT

104.2

You have tried to edit a coordinate that the current ST or BS refers to. You cannot
change a coordinate if the current ST or BS refers to it.

Press any key to return to the Data view screen.

Can't Edit XYZ from measurement

104.3

You have tried to change the coordinates of an SO, SS, or CP record. You cannot
change the coordinates of an SO, SS, or CP record.

Press any key to return to the previous screen.

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands