Nikon NPL-302 Series Instruction Manual Download | Manualshive

Page: 168 / 234

background image

5

Menu Key

148

Pulse Laser Station NPL-302 Series Instruction Manual

All observations from the station that you selected
are deleted.

Editing records

52.3

For any point record, you can edit the point name (PT), feature code (CD), height of
target (HT), height of instrument (HI), backsight point (BS), and backsight azimuth
(AZ).

Editing raw records

1.

Do one of the following:

–

In the RAW screen, highlight the record
that you want to edit. Then press the

Edit

softkey.

–

In the detailed data screen, press the

Edit

softkey.

2.

Use

[^]

or

[v]

to highlight a field. Then modify

the value in the selected field.

When you delete a ST record in the raw data view or the station data view, all the
observation data from the station is also deleted.

You cannot edit the CD field for SO, F1, or F2 records.
You cannot edit the HA, VA, or SD values.

«
...
166
167
168
169
170
...
»

Summary of Contents for NPL-302 Series











































































































































































































































Reviews:

No comments

Related manuals for NPL-302 Series

SMatrix DMX2400

Brand: dallmeier Pages: 12

Brand: Make Noise Pages: 15

Brand: Major tech Pages: 40

Brand: GMC-I Prosys Pages: 10

Brand: S&S Northern Pages: 5

Brand: Trebs Pages: 44

Greenlee CLM-1000

Brand: Textron Pages: 36

Brand: Vigor Equipment Pages: 12

Brand: Hanna Instruments Pages: 28

Brand: Lutron Electronics Pages: 23

Brand: VOLTCRAFT Pages: 8

Brand: Hanna Instruments Pages: 2

Brand: YOKOGAWA Pages: 169

Brand: Nahita Pages: 2

Brand: Keysight Pages: 14

Brand: OHAUS Pages: 64

Brand: Würth Pages: 28

Brand: R&S Pages: 135

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands