Nikon NPL-302 Series Instruction Manual Download

Page: 110 / 234

Applications

Pulse Laser Station NPL-302 Series Instruction Manual

Program Key

4.1

To display the Programs menu, press

[PRG]

Measuring distance and offset values along a specified line

41.1

Press

[1]

or select

2Pt RefLine

in the

Programs menu.

Enter the first point for the reference line.
Alternatively (to enter the point by
measuring), press the

MsrPT

softkey.

Enter the second point for the reference line.

Enter an asterisk (*) in the PT field to perform
a wildcard search. A list of matching points
appears. Highlight a point in the list and then
press

[ENT]

Direct Measurement screen

Press the

MsrPT

softkey to display a direct

measurement screen.
Sight the target and press

[MSR1]

[MSR2]

. The

Record PT screen appears.
If you press

[ESC]

in the Record PT screen, the

measured point is used but not recorded in the
job.

Summary of Contents for NPL-302 Series











































































































































































































































Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands

Nikon NPL-302 Series, Instruction Manual

Search results

Summary of Contents for NPL-302 Series

Reviews:

Related manuals for NPL-302 Series

Brands by name

Popular brands