manualshive.com logo in svg

Nidek Medical RT-5100, Operator'S Manual

Share
Download
Nidek Medical RT-5100 Operator'S Manual Download Page 93

75

OPERATING PROCEDURE

Chart Presentation

2

2.6.2

Visual acuity chart mask functions

<      >

<      >

<<<<

      >>>

>

Mask keys

Press any mask key on the control box to use the mask functions.

• The SC series displays the isolated segment in the 

center of the screen instead of isolating the chart with 
mask functions.

How to isolate a vertical line

Press 

< or >

.

When the vertical line is isolated:

• Press 

< or >

. 

 The isolation moves to the left or 

right. (When the same key is pressed again to continue 
moving an isolation located at one end of the chart, short 
beeps are audible and the isolation moves to the opposite end of the chart.)

• Press 

 or 

. 

 The isolation moves up or down.

• For charts with four columns on the SSC, the vertical isolated line is moved between only 

the two columns in the middle.

How to isolate a horizontal line

Press 

. 

 The top line is isolated.

Press 

. 

 The middle line is isolated.

Press

 

. 

 The bottom line is isolated.

When the horizontal line is isolated:

• Press 

 or 

. 

 The isolation moves up or down.

• Press 

 (only SC series). 

 The letter order is randomly rearranged at the same VA. When a                 

single VA is displayed (low visual acuity etc.) for the cortical vision letter, vertical line letter, or 
single letter, the letter order is also randomly rearranged at the same VA.

• Press

 

 (only SC series). 

 The letter order is randomly rearranged at the same VA.

• The VA value is automatically entered. (Except for when in Prism mode)

161221687130 承認済

Uncontrolled copy when printed.

Summary of Contents for RT-5100



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands