manualshive.com logo in svg

Nidek Medical RT-5100, Operator'S Manual

The Nidek Medical RT-5100 service manual is available for free download on our website. This comprehensive manual provides in-depth instructions and information for maintaining and servicing your RT-5100 device. Get the manual directly from our website and enhance your product knowledge and troubleshooting skills.

Share
Download
background image

272

APPENDIX: Standard Programs

8.8

Standard Programs

The RT-5100 has five programs of A, B, C, D and E, which can be programmed by the user.
The following standard programs have already been written in Programs A and B as factory setting.

Program A: Precision course 1

The final prescription is obtained after the monocular full correction (subjective data) is stored. The 
binocular balance test and auto adjustment are performed in the final field. Then the precise addition 
power is measured with the cross grid for near point in the subjective field.
(R: right eye, L: left eye, B: binocular eye)

1. AR data entry

Enter the AR data.

<Unaided field>

2. Unaided VA test

Measure the unaided VA.

<Aided field>

3. LM data entry

Enter the LM data.

4. Aided VA entry

Measure the aided VA.

<Subjective field>

5. R: AR data check

Check that the VA is about 20/30 in the AR data.

6. R: Red-green test

Spherical refinement with the red-green chart (fog + 0.5)

7. R: Cross cylinder test (axis)

Measure the cylindrical axis with the cross cylinder lens.

8. R: Cross cylinder test (power)

Measure the cylindrical power with the cross cylinder lens.

9. R: Red-green test

Spherical refinement with the red-green chart (fog + 0.5)

10. R: Best possible VA check (monocular full correction) 

Best possible VA on the chart with the most plus power

11. L: AR data check

Check that the VA is about 20/30 in the AR data.

12. L: Red-green test

Spherical refinement with the red-green chart (fog + 0.5)

13. L: Cross cylinder test (axis)

Measure the cylindrical axis with the cross cylinder lens.

14. L: Cross cylinder test (power)

Measure the cylindrical power with the cross cylinder lens.

15. L: Red-green test

Spherical refinement with the red-green chart (fog + 0.5)

16. L: Best possible VA check (monocular full correction)

Best possible VA on the chart with the most plus power

<Final field>

17. B: Binocular balance test

Test the binocular balance.

18. B: Stereo test

Check the steroscopic vision and enter the stereoparallax

19. B: Power adjustment (auto)

Power adjustment depending on the purpose (auto adjustment)

161221687130 承認済

Uncontrolled copy when printed.

Summary of Contents for RT-5100



















































































































































































































































































































Reviews:

No comments

Related manuals for RT-5100

Bacharach 100 Operation & Maintenance Manual preview
100
Brand: Bacharach Pages: 64
B meters HYDROCLIMA 2 Installation Manual preview
HYDROCLIMA 2
Brand: B meters Pages: 18
B meters HYDROCAL-M4 Operating And Installation Instruction preview
HYDROCAL-M4
Brand: B meters Pages: 14
Danfoss EKC 201 Manual preview
EKC 201
Brand: Danfoss Pages: 6
Omano CX-3 User Manual preview
CX-3
Brand: Omano Pages: 14
Xylem YSI Pro1030 User Manual preview
YSI Pro1030
Brand: Xylem Pages: 19
Barksdale BLP1 Operating Manual preview
BLP1
Brand: Barksdale Pages: 2
ASCEL Electronic AE20401 Assembly And Operation Manual preview
AE20401
Brand: ASCEL Electronic Pages: 64
MICRO-EPSILON ODC 2600-40 Operating Instructions Manual preview
ODC 2600-40
Brand: MICRO-EPSILON Pages: 82
Alfa Laval TE67D 1 Series Instruction Manual preview
TE67D 1 Series
Brand: Alfa Laval Pages: 18
MADDALENA Arrow Mobile Android Quick Start Manual preview
Arrow Mobile Android
Brand: MADDALENA Pages: 12
Eastwood Guitars WARREN ELLIS SIGNATURE TENOR BARITONE Setup Manual preview
WARREN ELLIS SIGNATURE TENOR BARITONE
Brand: Eastwood Guitars Pages: 4
Fluke 87V Ex Calibration Manual preview
87V Ex
Brand: Fluke Pages: 32
red lion DITAK 8 Manual preview
DITAK 8
Brand: red lion Pages: 4
Campbell HydroSense II User Manual preview
HydroSense II
Brand: Campbell Pages: 37
Farnell MarMonix MSL-765 User Manual preview
MarMonix MSL-765
Brand: Farnell Pages: 15
Shimadzu TOC-V CPH User Manual preview
TOC-V CPH
Brand: Shimadzu Pages: 22
Ress SK7 Manual preview
SK7
Brand: Ress Pages: 11

Brands by name

Popular brands

Load more brands