manualshive.com logo in svg

Nidek Medical RT-5100, Operator'S Manual

Share
Download
Nidek Medical RT-5100 Operator'S Manual Download Page 222

204

TEST METHOD

Negative Relative Accommodation (NRA) Test

4.11 Negative Relative Accommodation (NRA) Test

Use: To measure the negative relative accommodation when both eyes are converged at a specified 
working distance
Chart: Near letter chart with a horizontal line isolation at 40 cm away from the patient’s eye (near point 

chart 7)

Confirm that the “SPH Far 

 Near” parameter is set to SPH + ADD.

For the Plus Package, see "5.2.6 #21 Negative relative accommodation (NRA)" (page 218).

1 

Press 

 while pressing 

.

[NPC], [NPA], [NRA], and [PRA] appear.

When the NPA test has been completed just before, skip this step.

2

Press [NRA].

Both measuring windows are opened.

*29

The NRA window is displayed.

3

Gradually turn the dial counterclockwise 
and press [Blur] when the chart appears 
blur.

The [Blur] indication is highlighted. It 
means that the value has been stored.

4

Gradually turn the dial clockwise and press 
[Recov] when the chart appears clearly again.

The [Recov] indication is highlighted. It means that the value has been stored.

Pressing [Blur] or [Recov] again clears the stored data.

*29.

Occluding either measuring window with 

 or 

 measures the near point of accommodation for either eye.

161221687130 承認済

Uncontrolled copy when printed.

Summary of Contents for RT-5100



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands