background image

18

CONNECTIONS

POWERDRIVE MD2R Installation guide

4948       - 2017.11 / d

en

3 - CONNECTIONS

• All connection work must be performed by 

qualified  electricians  in  accordance  with  the  laws  in 

force in the country in which the drive is installed. This 

includes earthing to ensure that no directly accessible 

part of the drive can be at the mains voltage or any other 

voltage which may be dangerous. 

•  The drive must be supplied via an approved circuit-

breaking device so that it can be powered down safely. 

• The optional isolator supplied with the drive does 

not isolate the drive input busbars. It must without 

fail be associated with a circuit-breaking device in the 

switchboard.

• The drive power supply must be protected against 

overloads and short-circuits.

• Check that the voltage and current of the drive, the 

motor and the mains supply are compatible.

•  The voltages on the connections of the mains supply, 

the  motor,  the  braking  resistor  or  the  filter  may  cause 

fatal electric shocks. The protective plates supplied with 

the drive must always be installed correctly to protect the 

user against direct electric shocks.

•  Only one permanent magnet motor can be connected 

to the drive output. It is advisable to install a circuit-

breaking device between the permanent magnet motor 

and the drive output to eliminate the risk of hazardous 

voltage feedback when performing maintenance work.

•  See also the recommendations in section 7.

3.1 - Location of terminal blocks

3.1.1 - Location of the fuse boards

Depending on rating, 

POWERDRIVE MD2R

 may include one 

or more identical fuses boards :

 - 

60T à 150T : 1 board

 - 

180T to 570T & 270TH to 500TH : 2 boards 

  - 600T to 1100T & 600TH to 900TH : 4 boards 

  - 1400T and 1700T & 1200TH and 1500TH : 6 boards 

The fuse board location is specified in §3.1.4

Position the F8 fuse according to the mains supply 

voltage

F1

F2

F3 F4 F5 F6

F9

F7

PX4

460V(T)

600V(TH)

480V(T)

690V(TH)

400V(T)

500V(TH)

P1

F8

400V(T) / 500V(TH)

460V(T) / 600V(TH)

480V (T) / 690V (TH)

P2

P3

P4

P6

P7 P8

Interface

board

output

Power

Input S1

Power 

Input S2

External

power input

Fan

Control

Fan1

Fan2

Fan3

Fan4

Fan5

•  On 

POWERDRIVE MD2R

 60T to 150T, the fuse board is 

located over the chassis.

•  On 

POWERDRIVE MD2R 

180T to 270T : the fuse board 

is located on the side of the drive’s chassis. To reach the fuse 

board, undo the 2 screws of the control terminal block to tip it  

forwards.

•  On 

POWERDRIVE MD2R

 340T to 1700T  270TH to 

1500TH, please refer to §3.1.4 to located fuse board

3.1.2 - Electronics and forced ventilation 

power supply

The control electronics and forced ventilation units are 

supplied through a single-phase transformer which primary 

is connected to terminals L1-L2 of the power supply. If 

necessary, this transformer can be supplied with an external 

power source (PX4 terminal block on fuse board).  

The neutral of the electronics power supply must 

not be connected to earth. 

•  Electrical characteristics :

Ratings

Voltage

Primary

T

400V±10% / 50Hz ou 

460-480V ±10% / 60Hz

TH

525-690V±5% / 50Hz

Voltage

Maximum power

Secondary 1

(Electronics 

power supply)

230 V 

isolated

100VA

Secondary 2

(Forced 

ventilation and 

auxiliaries power 

supply) 

230 V 

connected 

to earth

60T to 75T :  

P = 300VA

100T to 150T :  

P = 500VA

180T to 270T :  

P = 2x500VA

340T to 570T :  

P = 2x1200VA

600T to 900T :  

P = 4x 1200VA

1400T to 1700T :   P = 6x 1200VA

270TH to 500TH :  P = 2x 1200VA

600TH to 900TH :  P = 4x 1200VA

1200TH to 1500TH : P = 6x 1200VA

3.1.3 - Characteristics of connection terminals

Refs.

Functions / 

connections

Type of connection and 

tightening torque

60T to 270T

Other ratings

L1, L2, L3,

ou   R, S, T

Mains power 

supply

M10 screw bolt - 20Nm

U , V, W

Motor outputs

PE

Earth

M10 bolt - 

20Nm

M8 bolts - 

12Nm

BR1, BR2

Braking resistor 

(1)

M8 screw bolt - 12Nm

P4, P5

EMC 

Commoning 

link

Torx screws Ø20 - 4Nm

-

Control 

block(2)

Spring terminal block

Do not exceed the indicated maximum tightening 

torque.

(1) If the optional braking transistor is already installed

(2) The neutral of the electronics power supply must not be 

connected to earth.

Summary of Contents for LEROY-SOMER POWERDRIVE MD2R 100T

















































Reviews: