Model NT-6598
Multi-Function, Rechargeable
Headlamp
The
NextLED Multi-Function, Recargeable Headlamp
is
designed to meet a wide variety of lighting applications. Its three
powerful, rechargable LED lights provide convenient, hands-free
lighting wherever you need it. It’s perfect for home repair work, auto-
motive repair work, bicycling, camping and more. Its 200 lumen spot
light gives focused lighting for detail work. It also has a low setting
(100 lumen) and handy strobe setting. And it tilts to put light right
where you need it. There’s also a wide beam light that’s perfect for
lighting larger, wider areas with even light. It also has three lighting
modes; high (300 lumens), low (100 lumens) and
a red light function for night lighting. The back battery pack has a
red safety light with a flashing red light mode. All three lights are
independently controled with their own switches. All this and it
recharges in as little as 2 hours.
CAUTION:
Read all instructions and warnings before operating!
SAVE THESE INSTRUCTIONS!
WARNING:
To avoid serious injury or death from electrical shock or fire:
1. This fixture
MUST ALWAYS BE USED IN ACCORDANCE WITH ALL
ELECTRICAL AND SAFETY CODES AND ORDINANCES
, including
the most recent National Electric Code (NEC) and with the
Occupational Safety and Health Act (OSHA) Volume 1 on General
Industry Standards and interpretations.
2.
ALWAYS
make certain that the power source conforms to the rating
on the fixture.
3
DO NOT
inspect or service the fixture while charging.
4. CAUTION:
Do not open, drop, short-circuit, incinerate, expose to
temperatures higher than 140ºF, or charge/use if damaged.
5. People with pacemakers should consult their physician(s) before
use. Electromagnetic fileds in close proximity to heart pacemaker
could cause pacemaker interferance or pacemaker failure
6. This fixture is not explosive-proof,
DO NOT
use in potentially
dangerous locations, such as in flammable or explosive
atmospheres.
7.
NEVER
operate the light with the clear protective plastic lens
broken or removed.
8.
NEVER LOOK DIRECTLY INTO LIGHT SOURCE
. LED’s are extremely
bright and can damage eyes with prolonged exposure.
9.
KEEP AWAY
from heating vents, radiators, or other sources of heat.
10.
KEEP OUT OF REACH OF CHILDREN
.
MAINTENANCE
Only qualified service personel must perform repairs. Opening or
visible attempts to open or repair work light will void any warranty
and/or cause damage to the product or personal injury.
CAUTION!
Do not use solvents such as gasoline,
turpentine, etc. to clean the unit. Aerosols and other
chemical will fog the clear polycarbonate lens.
LITHIUM BATTERY SAFETY WARNINGS
LITHIUM BATTERIES STORE A LARGE AMOUNT OF ENERGY AND
WILL VENT FIRE OR EXPLODE IF MISTREATED:
1. Keep work light dry after use
2. DO NOT DO ANY OF THE FOLLOWING TO BATTERY PACK:
a. Drop
d. Puncture
b. Open
e. Incinerate
c. Short-circuit
f. Expose to temperatures
greater than 140ºF
3. Charge work light only according to these instructions
OPERATION/CHARGING
1. Wide Beam Light:
The switch to operate the wrap
around light is located to the left
of the light as you face it (1.). Press
once for high mode, press again
for low mode and press a third time
for the red light. Pressing it a fourth
time turns the light off.
2. Spot Head Light:
The switch to operate the spot
head light is located on the top
housing of the spot light (2). Press
once for high mode, press twice
for low mode and press a third
time to activate the strobe function.
Press a fourth time to turn ligh
off. You can control the position
of the light by rotating the light
head up or down to place beam
where you want it.
3. Tail Light
The rear light switch is located on
the battery pack on the back of the
headband. The switch is directly
below the light (3.). Pressing once
activates the red light. Pressing it a
second time activates the flashing
red light. Pressing it a third time
turns on the sequential red light.
Pressing a fourth time turns light off.
Battery Charging:
Use the USB charging cable that came with this product. Plug one end
into the port located on the battery compartment, next to the frame
that contains tail light. Plug the other end into your USB charging de-
vice. While charging the tail light will flash. When fully charged, the tail
light will stop flashing and display solid red. Disconnect USB cord and
Headlamp is ready for use.
WARNING!
Charge while indoors only.
WARNING!
Always use the provided charging cable and a 5V adapter
(not provided). Using a non-compatible cable and charger could cause
damage to the Head Light or personal injury.
1.
2.
3.
