Next 877740 Assembly Instructions Manual Download Page 1

Tools Needed

Helpline

If you have any problems with this product or require

any replacement fittings please contact Customer

Services Tel: 0844 844 8999

 Avoid keeping furniture in direct sunlight or close to any heat sources as this can cause cracking, discolouration or

warping.

 Never drag pieces of furniture across the floor as this will cause damage to the joints.

ASSEMBLY INSTRUCTIONS.

IMPORTANT

 We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions. 

 Carefully check that you have all parts before beginning assembly.

 Keep fittings out of children's reach and keep children well away from the construction area.

 We recommend that the packaging is used to protect the surfaces during assembly.

 Do not put hot dished directly on the surfaces of the item.

 Ensure the product is protected with mats and coasters when items are placed on the surfaces, to prevent scratching

PRODUCT INFORMATION

IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.

• 

Made in China.

• Do no

t use this item if any structual part is broken or missing.

Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the item is found

to be faulty. Should you need to return the unassembled product, please repack in the original packaging.

 Made fro    metal base, MDF and solid wood with a painted finish.

m

CARE INSTRUCTIONS

 A minimum of 

2

 persons is required to assemble this product.

• 

All assembly fixings should always be tightened properly and periodically check all fixings and tighten if necessary.

• 

All assembly fittings should always be tightened properly.

• 

Always use a non-silicone based furniture polish. Silicone in furniture polishes can break down the lacquer finish.

• D

o not use abrasive cleaning products or those containing silicone.

 Gloss finishes are prone to light surface scratch and it is therefore very important that you  care for this item

correctly.

• For general cleaning, periodicall

y dust with a soft clean lint-free cloth or a soft micro fibre cloth. Please note soft

cloths (including yellow dusters) contain abrasive fibres which can lightly scratch the surface, if in doubt please try

your cloth in an inconspicuous area of the furniture first to assess its suitability.

 Do not rub or scrub the surface when cleaning.

 Any spills should be removed immediately with a soft clean damp cloth and dried immediately.

877740 GLOSS TURNED TABLE

   

Page 1 of 8

•  Please remove the plastic protection film on the table top b

efore use.

or damage.

Summary of Contents for 877740









Reviews: