Nexo NXAMP4x1mk2 User Manual Download Page 44

Page: 44 / 70

ALERTS LIST

PAGE 44 / 70

NXAMPMK2 USER MANUAL

ENERGY SAVER ENABLED

When enabled, the amplifier goes to Energy Saver Mode when no input signal has been received during a
given time interval. The power consumption is then reduced. When input signal is received again, the
amplifier leaves the Energy Save Mode.

You can adjust the No-signal time interval from 1 minute to 3 hours.

You can adjust the No-signal threshold level from -70 dBFS to

– 60 dBFS.

By default, Energy Saver Mode is disabled.

DPU MODE

See Chapter DPU Digital Patching Unit for NXAMP.

ALERTS LIST

GLOBAL

MAINS1 VOLTAGE(V)

The mains 1 voltage is out
of the limits
Over 276[V] (4x1/4x2)
Under 60[V] or over 276[V]
(4x4)

Automatically  shut  down
and  reboot.  After  reboot,
Error  Screen  displayed
until

the

causes

are

removed.

A. The connection
between the power source
and the amplifier might be
wrong.
B. Unstable power source.

Check AC power
connection

MAINS2 VOLTAGE(V)

– ONLY 4X4

The mains 2 voltage is out
of the limits
Under 60[V] or over 276[V]

Automatically  shut  down
and  reboot.  After  reboot,
Error  Screen  displayed
until  the  causes  are
removed.

A. The connection between
the power source and the
amplifier might be wrong.
B. Unstable power source.

Check AC power
connection

POWER SUPPLY1 VOLTAGE(V)

The output of the power
supply is out of the limits

Automatically  shut  down
and  reboot.  After  reboot,
Error  Screen  displayed
until  the  causes  are
removed.

The power supply unit of
the

amplifier

might

malfunction due to some
unexpected reason.

Call service center

POWER SUPPLY2 VOLTAGE(V)

– ONLY 4X4

The output of the power
supply is out of the limits

Automatically shut down
and reboot. After reboot,
Error Screen displayed until
the causes are removed.

The power supply unit of
the

amplifier

might

malfunction due to some
unexpected reason.

Call service center

Summary of Contents for NXAMP4x1mk2







































































Search results

Summary of Contents for NXAMP4x1mk2

Reviews:

Related manuals for NXAMP4x1mk2

Brands by name

Popular brands

Nexo NXAMP4x1mk2, User Manual

Search results

Summary of Contents for NXAMP4x1mk2

Reviews:

Related manuals for NXAMP4x1mk2

Brands by name

Popular brands