background image

WARNINGS

 

 

 

ePS10

 

Page 

3

 / 

18

 

 

WARNINGS

 

PRECAUTIONS 

Do not open the speaker, do not try to disassemble it neither to modify it in any way. The system doesn’t include any user-
repairable part.  

If the system seems to be malfunctioning or damaged, stop using it at once and have it repaired by a NEXO qualified technician. 

Do not expose the system directly to the sun or to the rain, do not immerse it into fluids, do not place objects filled with liquid on the 
system. If a liquid gets into the system, please have it inspected by a NEXO qualified technician. 

The connection should be performed by qualified technician, by ensuring that power is off. 

Operating temperature with temperate climate: 0°C to +40°C (+32°F to +104); -20°C à +60°C (-4°F to +140°F) for storage. 

SAFETY INFORMATIONS 

Read this manual before using the speaker. 

Keep this manual available for further reference. 

Observe all warnings and cautions. 

Please check the NEXO Web site 

nexo-sa.com 

to get the most up-to-date version of this manual. 

Ensure you are aware of the safety rules applying to rigging, stacking or installing on tripod or speaker stand. Failure to observe 
these rules may expose persons to potential wounds or even death. 

Only use the system with accessories specified by NEXO. 

Please always consult a NEXO-accredited technician if the installation needs architectural works and observe following precautions: 

Mounting Precautions

Please select screws and mounting location supporting 4 times the system weight. 

Do not expose the system to excessive dust, vibrations, to extreme cold or hot temperatures, to reduce the risk of 
damaging components. 

Do not place the system in an unstable position: it could fall accidentally. 

If the system is u

sed on a tripod, please ensure the tripod’s specifications are adapted and that its height does not exceed 

1.40m/55”. Do not move the tripod with the system in position. 

      

Connection and Powering Precautions: 

Unplug connected cables before moving the system. 

Power off the system before connecting the system. 

When switching on the installation, the amplifier must be powered last; when switching the installation off, shut off the 
amplifier first. 

If you work by cold temperatures, progressively raise the level to nominal value during the first minutes of use, to allow the 
system components to stabilize. 

Please check regularly the system condition. 

HIGH SOUND PRESSURE LEVELS 

Exposure to very high sound pressure levels may cause permanent hearing losses. Degrees of hearing losses may be different 
from one person to another, but almost everybody will be affected if exposed to high sound pressure levels during a long period of 
time. The OSHA (Occupational Safety and Health Administration) American Agency specified the following maximal exposures: 

Number of Hours 

Sound Pressure Level (dBA), 

 Slow Response 

90 

92 

95 

97 

100 

1 ½ 

102 

105 

½ 

110 

¼ or less 

115 

WASTE OF ELECTRIC OR ELECTRONIC EQUIPMENT 

This symbol on the product or its packaging indicates that this product must not be treated as household waste. 
Instead, it is your responsibility to hand it over to a designated collection point for the recycling of waste 
electrical and electronic equipment. By ensuring your waste equipment is recycled, you will help prevent 
potential negative consequences for the environment and human health, which could appear if this product was 
not recycled. Recycling helps spare natural resources. For more information about the recycling of this product, 
please contact your local city office, your household waste disposal service or your reseller. 

Summary of Contents for ePS10



















Reviews: