Newland NLS-BS80 User Manual Download Page 192

Page: 192 / 264

176

Custom Prefix

Enable/Disable Custom Prefix

If custom prefix is enabled, you are allowed to append to the data a user-defined prefix that cannot

exceed 11 characters.

For example, if barcode data is “123” and custom prefix is “AB”, the host device will receive “AB123”.

Disable Custom Prefix (default)

Enable Custom Prefix

Set Custom Prefix

To set a custom prefix, scan the

Set Custom Prefix

barcode, the numeric barcodes that represent the

hexadecimal value of desired prefix(es) and the

Save

barcode.

Note:

A custom prefix cannot exceed 11 characters.

Set Custom Prefix

Example: S

et the custom prefix to “CODE” (Hex: 0x43/0x4F/0x44/0x45)

Scan the

Set Custom Prefix

barcode.

2. Scan the numeric

barcodes “4”, “3”, “4”, “F”, “4”, “4”, “4” and “5” from the “Digit Barcodes (1D

Scanner)

” section in Appendix.

3. Scan the

Save

barcode from the Save/Cancel Barcodes (1D Scanner)

” section in Appendix.

Summary of Contents for NLS-BS80









































































































































































































































































Search results

Summary of Contents for NLS-BS80

Reviews:

Related manuals for NLS-BS80

Brands by name

Popular brands

Newland NLS-BS80, User Manual

Search results

Summary of Contents for NLS-BS80

Reviews:

Related manuals for NLS-BS80

Brands by name

Popular brands