5 Menu tree
5.4 MAIN MENU – Config
FST-2_HB.EN12/05
117
Car panel module –
Lamp type
Type of lamp for car call acknowledgement (important to avoid
flickering).
LED
Filamt
Car panel module –
Display 0
Function of pin X4.39 on the FPM car panel module. See
“Display 0 .. 2” on page 122.
00000000 ..
11111111
Car panel module –
Display 1
Function of pin X4.38 on the FPM car panel module. See
“Display 0 .. 2” on page 122.
00000000 ..
11111111
Car panel module –
Display 2
Function of pin X4.5 on the FPM car panel module. See
“Display 0 .. 2” on page 122.
00000000 ..
11111111
Car panel module –
OPEN = A+B
The door open signal (FPM X4.35 / X4.36) is active for all car
doors.
YES
NO
Car panel module –
CLOSE = A+B
The door close signal (FPM X4.2 / X4.3) is active for all car
doors.
YES
NO
Car panel module –
OPEN = last
The door open signal (FPM X4.35 / X4.36) is only active for
the car door last opened.
YES
NO
Car panel module –
Divider-Door
Car door control for lifts with a too large footprint of the car.
This parameter must only be activated if there is only one car
door. If this parameter is activated, the FPM input “Open door
B” (X4.35) is used to query the door divider contact (normally
closed!). If the divider door is open, the input is deactivated
and the car will be shut down on the current floor with
“OVERLOAD”. The “OVERLOAD” state can be reset with
input “Priority car” on the FPM (key switch on car panel,
X4.37).
YES
NO
Car panel module –
Card Reader
Control of a card reader to enable car calls. Only activate after
consulting NEW LIFT. This function requires a modification of
the system specific wiring! If this parameter is activated, no car
calls can be placed without a card reader!
YES
NO
Car panel module –
-"- Clear Opt
Delete pending car calls when activating the card reader.
YES
NO
Car panel module –
Chime–Roof
Separate approach chime for upward travel installed on the
car roof. The chime signal is issued on FPM output „Display 1“
(X4.38), if parameter
Display 1=00000000
is set (see
“Display 0 .. 2” on page 122).
YES
NO
Car panel module –
Chime–Floor
Separate approach chime for downward travel installed under
the car floor. The chime signal is issued on FPM output
„Display 2“ (X4.5), if parameter
Display 2=00000000
is
set (see “Display 0 .. 2” on page 122).
YES
NO
Car panel module –
DoorOpen NC
Interpret the door open signal (FPM X4.35 / X4.36) as
normally closed contact.
YES
NO
Car panel module –
O-Load Flash
Activate flashing mode of the overload display (FPM X4.6).
YES
NO
Car panel module –
Pin-34 Functn
Function of input X4.34 of the FPM (see “Pin-34 Functn” on
page 123).
0 .. 99
Car panel module –
Xtra.Inputs
Activate additional inputs for special functions on the car panel
module.
YES
NO
Car panel module –
3×Call=Clear
An already acknowledged car call can be deleted by placing
the call another three times.
YES
NO
Car panel module –
HEX+n Offset
Start value of the binary code for FPM position indicators.
0 .. 15
Menu item
Description
Setting range
Summary of Contents for FST-2
