New Holland Speedrower 200 Service Manual Download

Page: 48 / 81

INTRODUCTION

Product identification - Product Identification Number (PIN)

Speedrower® 200 [YDG670501 - ]
Speedrower® 240 [YDG670501 - ]

The windrower identification plate

(1)

is located on the left

side of the frame, next to the platform steps

(2)

. The iden-

tification plate includes the model number and the PIN.

NOTE:

The identification number of the windrower is re-

quired when ordering service parts. Record the numbers
in the front of this manual. These numbers may also be
required to identify a stolen windrower.

Plate information:

• Product Identification Number (PIN)

• Model designation

• Rated net power

• Model year

• Year of construction

• Permissible rear axle load

• Permissible front axle load

• Total permissible mass

NHIL13WR00059AA

47698329 14/04/2014

Summary of Contents for Speedrower 200


















































































Search results

Summary of Contents for Speedrower 200

Reviews:

Related manuals for Speedrower 200

Brands by name

Popular brands

New Holland Speedrower 200, Service Manual

Search results

Summary of Contents for Speedrower 200

Reviews:

Related manuals for Speedrower 200

Brands by name

Popular brands